blind hole
英 [blaɪnd həʊl]
美 [blaɪnd hoʊl]
盲穴；遮掩洞；闷眼；盲孔
双语例句
- An Analysis of the Machining and the Technological Improvement of Blind Hole Threads of a Carburetor Body
化油器本体盲孔螺纹的加工分析及工艺改进 - The optimum anode for deep hole, blind hole and filling plating processes.
深孔，盲孔及填孔电镀的最佳阳极。 - Finally, uses the blind hole law to examine its stress again.
最后，再用盲孔法检测其应力。 - Application of Improved Blind Hole Method to Welded Iron Tower Joint for Stress Relieving with Heat Aging
改进型盲孔法在铁塔焊接接头热时效消除应力中的应用 - Form and position measurement of blind hole of deep cavity based on endoscopic optical path
基于内窥光路的深腔盲孔形位检测及应用 - At least one loop of absorption blind hole is evenly distributed around the segmental concave cavity along the radial direction of plane.
径向面上沿圆缺凹腔周围均匀分布不少于一圈的吸收盲孔； - On the basis of the conclusion, the influence of the depth and diameter of blind hole on the gun body strength was studied.
并在此基础上，研究了盲孔直径及深度对射孔枪强度的影响。 - Retaining mechanism, with a tiny stroke clearance, solves the problem of high precision machining on small pieces and blind hole pieces.
冲程间隙极小的锁紧机构更能解决短小零件及盲孔零件等高精度加工难题。 - Study on the A 、 B values in calculating formula of blind hole technique
盲孔法测定时计算公式中A、B值的研究 - Blind hole method is a common method which is widely applied in the project to measuring residual stresses.
盲孔法是工程中被广泛应用的测定残余应力的方法之一，相移云纹干涉方法可得到孔边任意一点的位移信息。 - The small blind hole method is used for the measurement of residual stress inside T joint.
采用盲孔法测定了丁字焊缝的残余应力。 - Research on the Filling of Dry Sand for Vertical Pipe with Bottom Blind hole for EPS Pattern
干砂对EPS模样垂直向下盲孔充填性的研究 - Discussion on estimating the blind hole during chemical grouting
化灌中对盲孔判定问题的探讨 - Research of Numerical Calculating Method for Elastic Release Coefficients in Blind Hole
盲孔法中弹性阶段释放系数的数值计算方法研究 - Reliability and precision of blind hole drilling method for determining high residual stresses
盲孔法测量高残余应力的可靠性与精确度 - This article discussed the manufacturing technology of multilayer PCB with buried and blind hole, also explained the key process control in detail.
本文阐述了埋盲孔多层印制板的制作工艺，并对关键工序的控制作了详细说明。 - This paper introduces the criterion of selecting pump, detonation mode, principle and action of inner blind hole perforator and tubing pump joint technology.
介绍了内盲孔射孔器与管式泵联作技术的选泵标准、起爆方式、原理和流程以及内盲孔射孔器的研制。 - In order to solve the problem of cleaning the remaining salt in blind hole on bottom cap of pressure vessel resulting in salt bath hardening, vacuum heat treatment technology test has been made.
为解决压力容器底盖盐炉淬火所存在的盲孔内残盐难以清洗的问题，对其作了真空热处理工艺试验。 - The method supplys grinding of deep blind hole a economic and reliable technology.
该方法为深盲孔的磨削加工提供了经济可靠的工艺方法。 - At the last we take the advantage of blind hole method for examine.
最后还用盲孔法进行了检验。 - The method of underground gasification with blind hole type is explained in short, the model test platform, test system and test process are also introduced, and the test results are analyzed.
简述了盲孔式地下气化方法，介绍了模型实验台、实验系统及实验过程，并对实验结果进行了分析。 - The numerical calculating method of elastic release coefficients in blind hole is mainly researched in this paper, besides, the utility of each method is discussed.
本文主要研究了盲孔法测量残余应力时在弹性阶段释放系数的数值计算方法，并讨论了不同方法的实用性。 - Based on the working principle of non-contact capacitance sensor, influence of the edge effect of gauge head and width of protecting ring are studied, gauge head for measuring blind hole is designed to sight the centers of two adjacent holes.
基于非接触式电容测孔传感器的基本原理，研究了电容测头的电场边缘效应的影响及保护环的宽度选择，设计了电容瞄准测孔传感器的测头用于对相邻小孔的中心进行瞄准定位； - Removing Device for Bearings in Small Blind Hole
一种小尺寸盲孔中轴承的拆卸装置 - Development and application of cut-off tool for the mandrel in small deep blind hole
小直径深盲孔中套料芯棒切断刀的研制和应用 - Under high temperature action, the structure and surface appearance of coal bodies around the blind hole gasifier have changed, and formed the distillation combine zone, which improves load carrying ability and integral stability for coal bodies around gasification stove.
盲孔炉四周煤体在高温作用下，其组织结构和表面形态都发生了质的变化，形成干馏组合碹，从而提高了气化炉周围煤体的承载能力和整体稳定性。 - Research and application of technology combined inner blind hole perforator and tubing pump
内盲孔射孔器与管式泵联作技术的研究与应用 - Comparison between Blind Hole Drilling Method and Magnetic Method
小盲孔法和磁性法测残余应力的比较 - The difference is big between the through-hole and blind hole, so the probability of the gradation value is calculated in accordance with the image, and the pass recognition and automatic matching of threshold value is finished through the gradation histogram.
通孔和盲孔图像差异大，可根据图像计算出各灰度值的概率分布，通过灰度直方图完成孔型识别和二值化阈值匹配。 - For the structure characteristic of blind hole parts and using characteristic of hydrocarbon cleaning agent, the vacuum technology is introduced to achieve better cleansing effect.
超声波真空清洗是一种新型的清洗工艺技术，针对盲孔类零件的结构特点及所用环保型碳氢清洗剂的使用特点，在超声波清洗中引入真空技术实现较好的清洗作用效果。